There are many models of Mazda 6 and people try to upgrade its stereo from time to time. There are many generations in this and techniques always like to keep themselves updated with the latest technology. But before selecting the newer versions of radios and replacing, the first step is to remove the former radio. This articles deals on how to remove the radio from Mazda 6. The steps that are given in this article can be worked on with models that were released between the years 2003 and 2008.

For completing this task you will require a socket wrench, pliers and a screw driver.

Put the gear in the neutral position, set the parking brake and turn off the engine. After following these steps, open the hood of the car and disconnect the wire from the negative terminal of the battery. It is absolutely necessary that you disconnect the battery from the car before proceeding to remove the radio from the car. If the battery is not disconnected from the car then there may be short circuiting or electrical shocks. So make sure that you follow this step for your own safety.

For removing the gear shift knob rotate it in the counter clockwise direction. After a few rotations you will find the knob loosening; after loosening it remove the gear shift knob. Now remove the console from the car. You will find that the console extends to the ashtray. After removing the console you will find a couple of screws located in the underside of the climate control panel. Remove both the screws by rotating them in counter clockwise direction, with the help of a screw driver.

The glove compartment is opened to gain access to the side-mounted bold of the radio. The sides of this compartment are squeezed simultaneously, and are made to be dropped down. Once this is done, the screws that are seen can be removed.

The assembly of the climate control is entirely removed. This panel also includes the middle covers of the air vent. Once this cover is removed, it is turned over and the remaining screws twelve in number that mounts the radio with the air vent and other climate control are removed. When these screws are removed fully, the radio is free to be removed.

The entire assembly containing control and radio is unsnapped. You will find twelve screws once the covers are removed. These screws are removed carefully with appropriate screw drivers. Radio will pop out once the twelve screws are removed. The negative terminal is connected back.

With the help of this article you would have learnt how to remove the radio from a mazda6. Follow the steps and enjoy the music with your new customized radio.

In this article we will discuss How to Program a Pioneer Radio. Car stereo from Pioneer company is known for its best quality of music that can be enjoyed while we are on drive. These days there are many attractive play stations. So one may like to tune to these stations. So this article assumes grater importance in guiding us through the steps needed to complete this job of learning to program the car radio of Pioneer. As Pioneer is a leading brand we can take this as a standard for other models. The procedure mostly remains the same for all other brands.

This article will guide you to program the Pioneer radio system easily and quickly. This article also lists the things that are required to program it. Once the radio station is programmed, you need not search for a radio station to listen to songs or news. You can simply press the buttons on the radio system to switch between the radio stations.

The programming work has to be done in a screen called preset screen. This screen is brought to view by pressing the list key. This key is provided on the stereo’s front side. The next step is to set the stations that you need. These stations are set with the help of a scroll called multi-control. This is also provided in the system.

We don’t need any special things to do this job. All that we require is car stereo . This programming of radio is so easy that any one can learn it without any expert understanding by just following the five simple steps given in this article.

In the first step there is one option called ‘list’ present in the stereo of the car at its front side. As we press this ,a preset screen can be seen.

Stop turning the scroll wheel when you find the radio station which has to be saved. Now, push and hold any of the numbers from one to six on the front of the radio. The station name will flash on the display screen as you hold the number key. Once the flashing of the station name stops release the button. The radio station is fixed in this number.

The radio can be operated to listen to these stations after the display is switched over to the normal screen. This can be done by clicking the BAND button. It may be given as ESC also. It will be provided in the system.

Now its time to get back to our original display screen . So we should just press the escape button present in the stereo of the car in front side. Sometimes band button can also make us come back to our original display. Refer Pioneer manual for car audio systems in order to find if there are any other extra options and some other useful tips and suggestions for this programming job. Thus in this article we have got very useful information on How to Program a Pioneer Radio in easy steps and without the useful of expensive complicated tools.

Depth of the music is very important for all those who are all music enthusiasts. They also aim at giving a powerful music and equally good sound. So they are more interested in developing such a stereo. The high range of music is generally handled by the speakers at the rear decks, door panels and at the dash. A sub woofer is no substitute for a device which can handle lower ranges which also separate a audio system and stock system. As far as an audio professional is considered he can handle the job of installing sub woofer to your system. Even an individual can try doing it. But how to install a sub woofer in a factory stereo?

There are few tools required for accomplishment of this task. The usage of such tools will reduce the man power required and makes it easy. It includes trim panel removals, Philips head screw driver, speaker wires.

The negative cable from the car’s battery is removed initially. The battery’s negative terminal is actually connected with the negative cable and to the car’s frame. The cable’s clamp is loosened with the use of a Philips screw driver. The clamp is removed and it is kept aside until the task is accomplished.

Then the amplifier position is located after which the manual is gone through for any kind of procedure to be followed. The woofer can be placed either in the cargo area at the rear back or the car’s trunk in the case of models like hatch backs or SUV. The speakers are then connected to the output corresponding to each input.

Fourth step is very important. The speaker wires should be connected with the positive and negative terminals of the amps correctly. The next step needs some attention. The wires of the speaker should be routed to the place where sub woofers are present. Suppose if the location of sub woofers is not near the amplifier then wires can be taken under the carpet of the vehicle. Use trim panel removal tool for prying of panels at the openings of the door. The trim panels can be replaced by hand itself after laying the wires under the carpet.

The carpets are lifted and the wires are routed through this. Hiding the wires gives a custom look and avoids clumsy look. The trim panels are replaced manually. To fit them properly, pressure must be applied uniformly through out the panel’s length.

After that is done we come to the last step. This seventh step is nothing but reconnecting the ground cable with the vehicle battery’s negative terminal. Fix the clamp on the lead and use the same Philip screw driver which we used for loosening now to tighten the clamp of the cable. Before starting to do this job always make sure if the output from the amplifier can be handled by the sub woofer added.

Knowing how to install a sub woofer in a factory stereo is of great importance in maintaining a car.